12 replies to this topic

[deltatango]

Hi all

Wonder if you can help me my Barcrest Club Blazer has been
going OK with no problems. Its been turned off for a a few
weeks and I got this error code as follows

"Alarm 19-7F Coin mech strim unknown coin"

Can you tell me how to fix it as I need to sell it
to raise cash for another hobby

Thanks for any help

Terry

[skabaz]

hello mate

first of all let the alarm run for about 30 seconds.

the alarm sound may go off after 15 seconds but the alarm code will still show on the display.

once this has run its course stick a coin in.

play the credit and then turn the machine off/on.

the error should now be cleared.

do this with all doors closed!!!!

if the error still appears then you have a faulty coin mech.

baz

[deltatango]

Done that the alarm still goes off as sonn as the coin
dropped into mech I did pull the mech out to have a
look but there are wires attached I can hear the coin
drop down into the coin box and sometimes it rejects
it into where you get a payout in front

any-other ideas ?

Terry

[lincs1]

Done that the alarm still goes off as sonn as the coin
dropped into mech I did pull the mech out to have a
look but there are wires attached I can hear the coin
drop down into the coin box and sometimes it rejects
it into where you get a payout in front

any-other ideas ?

Terry

with the machine switched off disconnect the main harness connector on the mech and remove the mech from the machine, then pull back the flap on the coin mech and see that there's no coins jammed, also check the separater to see that no coins have clogged up in there aswell.

failing the above then as baz said your looking at a replacement mech which u will be able to buy from ebay for about 15 pound


hope this helps



lincs1

[deltatango]

Thanks guys

I pulled out the top coin mech and
also the the middle part that slides out
checked if any coins jammed none at all

pulled out and put back in connectors to
see if that made difference but no go

is it the top part that would need replacement

Terry

[£6 In Tokens]

:devil:

[lincs1]

:devil:

i give up!!

[damoyoung]

:devil:

I've seen a reply like this before...:empty: !

[skabaz]

you would need to get the top part replaced(the bit that has was make and model the coin mech is)

baz

[lincs1]

you would need to get the top part replaced(the bit that has was make and model the coin mech is)

baz

whats that in english baz? hahaha


i thinks its a mars ME126 fella if i'm not mistaken



lincs1

[skabaz]

i should really check what i write!!!

it was meant to say the bit that tells you what make and model the coin mech is!!!

baz

[damoyoung]

Hi all

Wonder if you can help me my Barcrest Club Blazer has been
going OK with no problems. Its been turned off for a a few
weeks and I got this error code as follows

"Alarm 19-7F Coin mech strim unknown coin"

Can you tell me how to fix it as I need to sell it
to raise cash for another hobby

Thanks for any help

Terry

Would this paragraph help assuming you have a Mars 126/129 ?

Insert into the machine a selection of all the coins/tokens shown on the validator
label. Acceptance of each one will be indicated by the LED flashing off once, and if
the coin/token is outside of the programmed window it will flash off twice. If the
LED flashes three time this indicates that the coin/token has been rejected by the
validator 4th sensor. Should the LED flash off four times this indicates either a

hardware or software inhibit is being applied.

Taken from the manual, not my words, but they seem like they'd be helpful!

[deltatango]

Had another fiddle with it to-day
stripped out the hopper coin mech
checked nothing stuck no coins
put back together and still has error

The coin mech is a SR5 Mars I think
these are a bit dearer than the others you
mention

I found a dealer where i live might give
him a ring see whats up but don't want
to spend much money as they are only
worth about £80 - £100

I suppose I could take the coin mech to
him to test it out to confirm its no good



Terry