2 replies to this topic

[neil2829]

Could someone please help me the coin alarm keeps going off and coming up with error 6.9 I have recently changed the coin mech so know its not that and the coins have started to go in the opposite boxes and in the hopper 20ps in £1 hopper £1 coins in 20p hopper IM SO CONFUSED can someone please HELP me out here would be much appreciated Thanks.

NEIL

[DaemonX]

Here's a post from DAD, taken from Bugs's reply previously.

These were posted on Fruit Forums ages ago by Bugs Bunny. I've always found them useful.

OLD ERROR LOG INFO - As used on Casino Las-Vegas, Big 50 etc

ERROR & EVENT CODES

CODE FAULT CAUSES (IN ORDER OF PROBABILITY)
1.1 £1 COIN INPUT }
1.2 50P COIN INPUT }
1.3 20P COIN INPUT }
1.4 10P COIN INPUT } Coin jam, Coin mech, Mother board.
1.5 20P TOK. INPUT }
1.6 5P COIN INPUT }
1.8 COIN MECH. ERROR More than one line high, Coin mech
1.9 STRIM ALARM Coin mech strim detected, Mother board.

2.1 / 2.8 REEL 1 - REEL 8 Opto tab missing/faulty, Mother board.
2.9 REEL DISCONNECTED Reel disconnected,Loom O/C, Mother board.

4.1* REFILL Refill keyswitch made.
4.2* RESET On board reset switch operated.
4.3* BUTTON Button stuck on power up.
4.4 DIRECT INPUT % Key missing, Mother board.
4.5 B/DOOR OPEN Back door open
4.7 C/DOOR OPEN Cash door open

* = Event code only. N.B. In the case of *4.3 the machine will on power up show the code and illuminate the stuck button for a short period of time before continuing to run in the normal manner.

5.1 RAM RESET Program or Processor Board
5.3 FRAUD (OFF/ON Alarm) Machine turned off/on during play (with full play credit).
5.5 MODE OF PLAY Mode of play key, Mother board.
5.7 COIN VERIFICATION Verification Opto (Hopper or Payslide)
5.9 COIN DETECT ERROR Hopper drive PCB, Motherboard.

6.1 METER 1 Cash in meter, Mother board.
6.2 METER 2 Cash out meter, Mother board.
6.3 METER 3 Token in meter, Mother board.
6.4 METER 4 Token out meter, Mother board.
6.5 METER 5 Refill meter, Mother board.

7.1 E.D.C TIMEOUT E.D.C. not fitted E.D.C. faulty, Mother board.
7.2 - 7.9 E.D.C Errors E.D.C. faulty, Mother board.

In the case of a protocol failure the code 7.1 will always be shown at the time of failure.

8.1 CHECKSUM FAIL Machine program changed.
8.2 RAM FAIL Processor board.
8.3 % CHANGE Change of aiming %. (new processor/program fitted)
8.4 MODE Mode of play changed.
8.5 RAM CORRUPTION Processsor board.
8.6 SOFTWARE RESET Program has performed a security reset.

9.0 / 9.1 SOFTWARE Processor board, program.
9.2 / 9.3 SOFTWARE/MPU Processor board, program.
9.4 SOFTWARE Program
9.6 WATCHDOG FAILURE Processor board

Any other code with a prefix of 9 indicates a fault on the mother or processr board, or software.
To assist in fault location the test routine must be entered to confirm if components (ie, lamps, level sensors, DIL switches etc) are electrically sound.
NEW ERROR LOG INFO




ERROR CODES
(Bacta 6 Standard Codes in Bold)


Code Sup Description
00 00 Unknown Error Occurred
01 00 Payout Verification Error
01 40 Non Payout 5p Cash
01 41 Non Payout 10p Cash
01 42 Non Payout 20p Cash
01 43 Non Payout 50p Cash
01 44 Non Payout 100p Cash
01 49 Non Payout 10p Token
01 4A Non Payout 20p Token
01 4B Non Payout 50p Token
01 4C Non Payout 100p Token

10 00 Payout Value Negative
10 01 20 Token Coin In Fault
10 02 ME129 More than 1 line high
11 00 £1 coin in fault
12 00 50p coin in fault
13 00 20p coin in fault
14 00 10p coin in fault
15 00 20p Token coin in fault
16 00 Note Acceptor Fault
19 00 Strim Error

20 00 General Reel Error
20 01 Reel 7 Opto Check Error
20 02 Reel 8 Opto Check Error
20 05 Reel Loom Reel Error
21 00 Reel 1 Opto Check Error
22 00 Reel 2 Opto Check Error
23 00 Reel 3 Opto Check Error
24 00 Reel 4 Opto Check Error

25 00 Reel 5 Opto Check Error
26 00 Reel 6 Opto Check Error
30 00 General Lamp Failure

40 00 General Operational Errors
40 01 Back Door Open
40 02 Back Door Closed
40 03 Cash Door Open
40 04 Cash Door Closed
40 05 Test Routine Activated
41 00 Refill Mode Entered
42 00 Memory Cleared
43 00 Button Stuck
44 00 No % key
46 00 Call Attendant
47 00 Refill Required
45 00 Payaim change occurred
48 00 On/Off Tamper Alarm
49 00 No Stakes / Prizes Keys


Code Sup Description
50 00 General Electronic Problems
51 00 EPROM Failure
52 00 PAL Error
53 00 Ram Check Fail
54 00 Hardware Error
55 00 Sparking Detected
56 00 PSU Fail

60 00 General Meter Fault
60 01 Meter Detect Fail, 7
60 02 Meter Detect Fail, 8
61 00 Meter 1 -(Cash In) Fault
62 00 Meter 2 -(Cash Out) Fault
63 00 Meter 3 -(Token In) Fault
64 00 Meter 4 -(Token Out) Fault
65 00 Meter 5 -(Refill) Fault
66 00 Meter 6 -(Prizes Out) Fault

70 00 General Dataport Error
70 07 BBX Lock Up
70 08 BBX Buffer Full
70 01 Data Carrier Lost Error
70 02 Framing Error Detected
70 03 Over Run Error
70 04 Parity error
70 05 Blackbox NAK/other rec’d
70 06 Blackbox Called And Active
71 00 Waiting for Dataport
72 00 Faulty Comms Link

88 00 Program Change

90 -9f Manufacturer Software Alarms
90 00 Attempt To Divide By Zero
90 01 Hundred Hertz List Full
90 02 Processor Bus Error
90 03 Address Alignment Error
90 04 Illegal Instruction
90 05 Autovector 6 Watchdog

91 00 Illegal Mode
91 01 Control Pointer Omitted

92 00 Mainboard Access Violation (S.A)
92 01 Credit Gone Negative
92 02 Hopper Fraud, Pulses seen

93 00 Data Logger Failed
93 01 Writing To Data Logger

94 00 Vend Out Not Seen, 1
94 01 Vend Out Not Seen, 2
94 02 Vend Out Not Seen, 3
94 03 Vend Out Not Seen, 4
94 05 Vend Tamper, 1
94 06 Vend Tamper, 2
94 07 Vend Tamper, 3
94 08 Vend Tamper, 4

HOWEVER... I notice 6.9 isn't there???????????? This 'may' help tho.

[impact]

Hi Neil and welcome to fruit Emu

ok your machine impact model 1, 2 or 3
coin mech using C435A green,yellow,purple SR5 / MS 126 Ref Blue or DFX orange with old mech did it use a green mpc unit so new 50`s and £2 coins could work

if your mech is put 20p and pounds in different hoppers or boxes then the route div is this pluged in ok or the routing plug diodes ok use a meter or a battery with a led as this sounds like you may not have the routing plug in for that mech (remember to turn the machine off first) dose the led on the coin mech look clear and bright

you tryed swapin the old mech back over to see this error if it comes back , dose the machine only alarm once the coin has gone through the mech or dose it alarm before you even put a coin in i.e after boot up

in the test routes meter test turn refill and see if every meter works thats even if the machine will let you get that far

try removing the meter loom off impact and resit it, are you using the old box red handle power supply or the orange type if so are all leds ok

as there is 3 or 4 things at fault 1 is psu. 2 mech 3.loom from where u may have got it shut between the front door and the cabnet/ trapped it in between the impact cover, 4. one of the meters have gone high and killed impact or knocked out all meters

error 6.9 is a meter error as you can tell, error 6.9 is like error 144 XX (not coin mech error but reels error)

if once tryed a number of things and still no joy i will ring jpm for you. and ps i am late for work.