33 replies to this topic

[Bencrest]

Also need battery for my Monte Carlo or bust and how bigs ya rock, so need like a bundle pack now lol we will have to meet up for a beer Ben, share some fruit machine memorys. I take it the batts on them are fairly standard

 

Honestly not sure about the batteries you would need. Assuming you can see the batteries OK, just grab some good photos and look at them on a PC. Otherwise, it'll be a case of removing the boards to make sure (or asking someone who knows what they are talking about, I haven't a clue about older machines!!)

 

As for meeting up for a beer, we may well have to do that

[straekseims]

Ive texed AAA but got no reply?

 

got a pic of batt from HBYR its a 3.6v and 110mah

 

the monte has loads in there so dont wanna move anything and upset it so that will have to wait

 

 

Attached Files

•  WP_000711.jpg   189.5KB   12 downloads
•  WP_000703.jpg   116.32KB   12 downloads

[SourceLeisure]

Are The Moving Parts In The Splitter (Bottom Of The Coin Mech Working) 
If Its Reading Credit (Its Likely Its Seperator Is Faulty,Jammed) 

Happend A Fiew Times,But For Time & Hassel (Replace Whole Unit) 

[straekseims]

It can work for £100s then balls up after ever couple of pound.

 

This is the Mech I need

 

 

Attached Files

•  WP_000722.jpg   107.3KB   12 downloads

[straekseims]

right I get a coin mech (SR5) from e bay and it all fires up ok but.....it won't accept any coins! The old mech just makes it alarm now, this new one I got off eBay n it all plugs in ok but like I say, it accepts nothing?????

Any ideas anyone?

I tried following the book but that don't work, drivin me mad!

[straekseims]

Any takers lol

[straekseims]

Old mech had "serial" written all over it so I guess new mech needs to be "serial" whick I think it is but don't know foe sure

[impact]

get yourself a another standard sr5 plug it into any fruit that uses the parrelle interface, Plug it in set the rote to E  turn the machine on the led will go green press the button on the mech led go`s red move back to the pos it was first in then press the button again turn off machine remove mech then thats it interface is now set for serial. BINGO!!

 

Ps you have about 15/25sec to do it in

[straekseims]

My alien is the only one that is series I think, pacman is mpu 6 SR5i I did try all that yesterday in the alien but won't let me reprogramme it, apparently U need some equipment to reprogramme a coin mech,

Been speaking to a lad named James who called on eBay "supernudgegambler" ?

He's gonna bell me tomoz for a possible solution.
If I hold the button down on the mech with the rotary switch on E the light just stays green, tried it like 10 times yesterday lol

[impact]

your not doing it right it needs to be in a parrell machine i.e a scorp4 or an normal mpu5. You can`t do it from a serial machine what the E= to is extend/Ext/enable port handle Par to Ser

Edited by impact, 07 March 2013 - 10:35 PM.

[straekseims]

Ahhhhhhhhhhhhhh I get ya, many thanks il try it in the pacman or perfect deal ?

[impact]

Perfects a scorp5 (serial machine ) your need an older unit that runs on scorp4 , As for pacman What one barcrest or Mazoma? Mazoma if its the old jpm electra cabnet model which will work on, Even jpm impact or pluto4 stuff done one day infact. What is a handy little number is to make up a loom 12V clean power supply on a par plug thats the big white one mostly common and do em like that.

[straekseims]

Pacman is mpu6 lol

You are right though impact, but my much won't do anything so he said he will set me one up on serial and send me that and to return this one

[impact]

Mpu6 model Yep Barcrest (Programmed using ibutton system / Abit like des key *hit also)

 

Ok fella cool beans