Posted 02 October 2017 - 05:51 PM
That is very recent - I got it off eBay for £15 ( well £23 when you add P&P ).
Had to make the base up - but yeah thanks, I was unsure about it but your comment has made me think yes absolutely. 
Looks fantastic mate,top job on this.
Many thanks mate.
It has changed the way I see layouts and made them even more enjoyable...
Member
Posted 02 October 2017 - 07:04 PM
That is very recent - I got it off eBay for £15 ( well £23 when you add P&P ).
Had to make the base up - but yeah thanks, I was unsure about it but your comment has made me think yes absolutely.
Many thanks mate.
It has changed the way I see layouts and made them even more enjoyable...
Yep I love it. I think it really sets the machine off. I'd have something like that myself but I don't have the room above the machine.
Member
Posted 24 December 2017 - 11:52 AM
You done a good job on that, Reg...
Hopefully i can make a MFME cab when i have saved up enough to get the parts, was thinking of having a 40" screen when i finally get round to it.
Member
Posted 24 December 2017 - 11:59 AM
Just a little udpate now the new MFME is out.
This is showing the full screen, stretch mode.
shift+F3
Brilliant Reg. Didn't realise the new version was out... will have a look at it now. Your cab looks brilliant!
Junior Member
Posted 06 January 2018 - 08:10 PM
one quick question what is the difference between 5v and 12v crimped wires will they both work .I understand that i need 6.3mm to fit into the buttons.The ipac 2,the pacdrive,16 buttons that illuminate, a usb connector and then i am good to go.Is that all i need? and then i will make something to house it in when its done.
Posted 06 January 2018 - 08:22 PM
Power for the LED's is provided by the pacdrive.
Basically I chain all the LED's together with a single source for the power that comes from the pacdrive and then you have the on / off signal come from the other terminals.
Perhaps the best way to show it is look at the keyboard building guide I did. That shows how to make one end to end ( pre-cabinet ), but I used the same method in the cabinet.
Here's the thread...
http://www.desertisl...mfme-keyboard/
The guide is here...
http://www.desertisl...-mfme-keyboard/
...or...
MFME_Keyboard_V1.00.pdf 5.15MB
5 downloads
Page 8 is going to show what it physically looks like with regards to the LEDs.
What you see there was the prototype to this...
1.jpg 146.81KB
0 downloads
2.jpg 160.1KB
0 downloads
...which then lead to this cabinet. Sadly due to space, that keyboard is sitting in the loft. 
Edited by Reg, 06 January 2018 - 08:23 PM.
Junior Member
Posted 06 January 2018 - 09:12 PM
if you want to make space in your loft i would be interested in buying it at the right price.
Posted 16 January 2018 - 10:54 PM
if you want to make space in your loft i would be interested in buying it at the right price.
To be honest, it means more to me as a sentimental value for the work that went into it then a cash value...
I saw this tonight, I would love one of these for my cabinet...
Posted 03 February 2018 - 09:30 PM
Had a couple of hours to spare this evening so topper got changed.
Had to replace all the internal leds with those cheap strips with a remote from Amazon, think it worked out well.
https://www.amazon.c...duct/B072F3GGGJ
I also have at least one £500 machine on the cabinet, so it's ok to put this there.
Edited by Reg, 03 February 2018 - 09:30 PM.
0 members, 1 guests, 0 anonymous users
